‘Clear out’ parts - collection at Stoneleigh if required

For Sale and Wanted Section
Post Reply
Martin D-S
T289R Member
T289R Member
Posts: 33
Joined: Thu Jan 06, 2011 12:59 pm
Location: Warwickshire

‘Clear out’ parts - collection at Stoneleigh if required

Post by Martin D-S » Sun Apr 28, 2019 9:59 pm

Hi, I’m having a clear out, and can take parts to Stoneleigh for collection, or despatch via Hermes at cost.

Lumenition Optronic PMA50 ignition module only, unused, but no box and small white block connector is absent, NOS (New Old Stock): £50.
Universal choke cable, 1.9m long, twist to lock, unused, NOS £4.
Universal bootlid support stay, min.length 29cm, max 49cm, used but good, 2 available, £5 each.
Universal bonnet or bootlid support stay, with ‘lift to release’ safely catch, min.length 32cm, max 55cm, scruffy but safe with great patina, £3.
Rover SD1 V8 9.5” 241mm clutch friction plate - genuine Borg & Beck 52509, New old stock: £45.
Rover V8 clutch release bearing and carrier, used but smooth rolling: £5.
Rover SD1 V8 sump with pick up pipe and baffle. Battered, dented and scraped, but doesn’t leak paraffin when tested: £10
Rover SD1 V8 front timing cover ERC0036, bare, with hole for dizzy: £70.
Range Rover V8 front timing cover HRC1321, bare with hole for dizzy: £70.
Rover SD1 V8 alternator mounting bracket ERC0303: £10.
Rover SD1 V8 41673A 35DE8 distributor with Opus electronics, bit scruffy but has the important skew gear with oil pump drive and rotor arm, so £30.
Range Rover V8 42649A 35DLM8 distributor with 9EM ignition module, scruffy but has the important skew gear with oil pump drive and rotor arm, so £30.
Rover V8 remote extension RKC3406 with gear-lever and knob for 5 speed manual gearbox - housing a bit worn on shaft supports, so ideal for rebushing or shortening: £25
Rover SD1 V8 water pump pulley for v-drive belt, scruffy: £3.
Rover V8 dipstick and tube, 53cm long: £3.

Please let me know if you’d like photos of anything.
Regards, Martin.

Martin D-S
T289R Member
T289R Member
Posts: 33
Joined: Thu Jan 06, 2011 12:59 pm
Location: Warwickshire

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by Martin D-S » Mon Apr 29, 2019 10:56 am

Hi, an update:-

Lumenition Optronic PMA50 ignition module only, unused, but no box and small white block connector is absent, NOS (New Old Stock): £50.
Universal choke cable, 1.9m long, twist to lock, unused, NOS £4.
Universal bootlid support stay, min.length 29cm, max 49cm, used but good, 2 available, £5 each. SOLD
Universal bonnet or bootlid support stay, with ‘lift to release’ safely catch, min.length 32cm, max 55cm, scruffy but safe with great patina, £3. SOLD
Rover SD1 V8 9.5” 241mm clutch friction plate - genuine Borg & Beck 52509, New old stock: £45.
Rover V8 clutch release bearing and carrier, used but smooth rolling: £5.
Rover SD1 V8 sump with pick up pipe and baffle. Battered, dented and scraped, but doesn’t leak paraffin when tested: £10 SOLD
Rover SD1 V8 front timing cover ERC0036, bare, with hole for dizzy: £70.
Range Rover V8 front timing cover HRC1321, bare with hole for dizzy: £70.
Rover SD1 V8 alternator mounting bracket ERC0303: £10.
Rover SD1 V8 41673A 35DE8 distributor with Opus electronics, bit scruffy but has the important skew gear with oil pump drive and rotor arm, so £30.
Range Rover V8 42649A 35DLM8 distributor with 9EM ignition module, scruffy but has the important skew gear with oil pump drive and rotor arm, so £30.
Rover V8 remote extension RKC3406 with gear-lever and knob for 5 speed manual gearbox - housing a bit worn on shaft supports, so ideal for rebushing or shortening: £25 SOLD
Rover SD1 V8 water pump pulley for v-drive belt, scruffy: £3.
Rover V8 dipstick and tube, 53cm long: £3.

Please let me know if you’d like photos of anything.
Regards, Martin

CobStang
Forum member
Forum member
Posts: 230
Joined: Sat Dec 10, 2011 3:21 pm

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by CobStang » Mon Apr 29, 2019 5:38 pm

PM SENT re 35DLM8

Thanks

User avatar
nikbj68
T289R Committee
T289R Committee
Posts: 1268
Joined: Thu Jul 17, 2008 3:31 pm
Location: Anglesey, North Wales.
Contact:

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by nikbj68 » Fri May 10, 2019 6:44 am

Thanks for all of my goodies!
Hawk 289 FiA...AT LAST!!!

Martin D-S
T289R Member
T289R Member
Posts: 33
Joined: Thu Jan 06, 2011 12:59 pm
Location: Warwickshire

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by Martin D-S » Fri May 10, 2019 11:45 pm

You’re welcome Nik - I’m pleased they’ll be put to good use!
Regards, Martin.

User avatar
nikbj68
T289R Committee
T289R Committee
Posts: 1268
Joined: Thu Jul 17, 2008 3:31 pm
Location: Anglesey, North Wales.
Contact:

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by nikbj68 » Sat May 11, 2019 2:53 pm

...Probably sit in the corner of the garage for a year or 2...! 😳🙄
Hawk 289 FiA...AT LAST!!!

stu60
T289R Member
T289R Member
Posts: 38
Joined: Fri Jul 08, 2016 10:09 am
Location: Cheltenham

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by stu60 » Mon May 13, 2019 5:46 pm

hi ,
is the dipstick and tube still available?
thx stuart

Martin D-S
T289R Member
T289R Member
Posts: 33
Joined: Thu Jan 06, 2011 12:59 pm
Location: Warwickshire

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by Martin D-S » Mon May 13, 2019 10:13 pm

stu60 wrote:
Mon May 13, 2019 5:46 pm
hi ,
is the dipstick and tube still available?
thx stuart
Hi Stuart,
Yes indeed.
Regards, Martin.

stu60
T289R Member
T289R Member
Posts: 38
Joined: Fri Jul 08, 2016 10:09 am
Location: Cheltenham

Re: ‘Clear out’ parts - collection at Stoneleigh if required

Post by stu60 » Mon May 13, 2019 10:28 pm

great. i think i have sent you a pm. let me know if you dont get it
thx Stuart

Post Reply