WANTED - Hawk style radiator for Rover V8.
I know it’s not an SD1 or MGB V8 design.
Has anyone swopped their Rover for a Ford and has a Rover rad left over.
Obviously needs to be in good leak free condition.
Peter C
Wanted - Rover radiator
Re: Wanted - Rover radiator
hi Peter
if you still have your old radiator... i had mine rebuilt by company below. Uprated core and they also brazed a couple of brackets and installed my 2 mishimoto fans to replace the original single. Looks like new and excellent quality job and not too expensive. i think they have other branch in Leicester(?). Advantage was i knew it would fit and no modding mounting holes or connections.
Gloucester Radiator Specialists
Lower Tuffley Lane
Gloucester
GL2 5DT
T: 01452 419524
F: 01452 382333
E: gloucesterrads@autocoolingcentre.co.uk
best regards
Stuart
if you still have your old radiator... i had mine rebuilt by company below. Uprated core and they also brazed a couple of brackets and installed my 2 mishimoto fans to replace the original single. Looks like new and excellent quality job and not too expensive. i think they have other branch in Leicester(?). Advantage was i knew it would fit and no modding mounting holes or connections.
Gloucester Radiator Specialists
Lower Tuffley Lane
Gloucester
GL2 5DT
T: 01452 419524
F: 01452 382333
E: gloucesterrads@autocoolingcentre.co.uk
best regards
Stuart
Re: Wanted - Rover radiator
I've used a radiator like this.
https://www.ebay.co.uk/itm/FORD-TALL-RA ... SwKtlWs0ln
4 core.
You can tweak the design to your needs, ie position of inlet and outlet, filler neck or not.
It just fits between the Hawk chassis rails.
https://www.ebay.co.uk/itm/FORD-TALL-RA ... SwKtlWs0ln
4 core.
You can tweak the design to your needs, ie position of inlet and outlet, filler neck or not.
It just fits between the Hawk chassis rails.
Kev Davies
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D
Re: Wanted - Rover radiator
Thanks guys.
I have found a radiator repair shop so might talk to them first.
As Stu says at least you know connections are in the right place.
Thanks for the contact Ken but I’m a bit nervous starting afresh especially as their sizes don’t appear to correlate to my existing one.
Peter C
I have found a radiator repair shop so might talk to them first.
As Stu says at least you know connections are in the right place.
Thanks for the contact Ken but I’m a bit nervous starting afresh especially as their sizes don’t appear to correlate to my existing one.
Peter C
Re: Wanted - Rover radiator
I have this one in the yellow Cobra and the same will go to the project:
https://www.ebay.co.uk/itm/50mm-ALUMINI ... SwS3NciReF
Works fine and cheap too.
https://www.ebay.co.uk/itm/50mm-ALUMINI ... SwS3NciReF
Works fine and cheap too.
You do not have the required permissions to view the files attached to this post.
Special customized BRA289
Re: Wanted - Rover radiator
Thanks for the info Migge,
I've done a quick check and my existing rad's core is a bit bigger in cross sectional area. 178 versus 172 CM2 plus mine is a four core at 63mm deep not 50mm. I don't think I would want to start again with fresh bracketry, ducting and different hoses.
I think that if the sealant I've just ordered doesn't work I will get the existing one repaired having found that there is a radiator repair shop in a nearby town.
Got to be cheaper than a brand new item.
Peter C
I've done a quick check and my existing rad's core is a bit bigger in cross sectional area. 178 versus 172 CM2 plus mine is a four core at 63mm deep not 50mm. I don't think I would want to start again with fresh bracketry, ducting and different hoses.
I think that if the sealant I've just ordered doesn't work I will get the existing one repaired having found that there is a radiator repair shop in a nearby town.
Got to be cheaper than a brand new item.
Peter C
Re: Wanted - Rover radiator
"K Seal" is the best leak stopper I've found in recent years.
Kev Davies
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D